3mm Green LED Indicator with Green Diffused Lens

3 year ago

0 0

Shenzhen Best LED Opto-electronic Co.,Ltd / BESTSMD CO LIMITED(HK)

 8 year year

Product details

3mm Green LED Single Level Circuit Board Indicator

This 312LGC-3.5HK green right angle circuit board indicator was made by 3mm green through-hole LED inside. Similar same as the WP934CB/GD from Kingbright. When we finished the production of green through-hole LED, we will install this 570nm LED to a black case and then bend the LED pins as right angle. In this case, this circuit board indicator can save much assembly cost and time. If you need some this circuit board indicator with other color, just feel free to contact us for more detail~

312LGC-3.5HK 3mm Green LED Circuit Board Indictor right angle

Size of 3mm Green LED circuit board indicator:

312LGC-3.5HK 3mm LED Circuit Board Indictor Size

Notes:

1, All dimensons are in millimeters;

2, Tolerance is ±0.10mm unless otherwise ntoed;

3，590nm LED(Yellow), 520nm LED(Pure Green) or 625nm LED (Red) are also available in this case.

Absolute Maximum Ratings(Tc=25℃)

Parameter	Symbol	Rating	Unit
Power Dissipation	Pd	105	mw
Pulse Forward Current	IFP	100	mA
Forward Current	IF	≤30	mA
Reverse Voltage	VR	5	V
Junction Temperature	Tj	100	℃
Operating Temperature	Topr	-40 - +80	℃
Storage Temperature	Tstg	-40 - +100	℃
Soldering Temperature	Tsol	260	℃
Electro-Stati-Discharge(HBM)	ESD	2000	V
Service lige under normal conditions	Time	80000	H
Warranty	Time	2	Years
Antistatic bag	Piece	1000	Back

*Pulse forward current confition: Duty 1% and Pulse width=10us.

*Soldering confition: Soldering confition must be completed with 3 secongds at 260℃

Electrical Optical Characteristics(Tc=25℃)0

Parameter	Symbol	Min	Typ	Max	Unit	Test Condition
Forward voltage	VF	1.8	1.9	2.4	V	IF=20mA
Luminous Intensity	IV	150		250	mcd	IF=20mA
Peak Wavelength	λP		570		nm	IF=20mA
Dominant Wavelength	λd	565	570	575	nm	IF=20mA
Half Width	△λ		12		nm	IF=20mA
Viewing Half Angle	2θ1/2		±22		deg	IF=20mA
Revers Current	IR			5	uA	VR=5V

*Luminous Intensity is measured by ZWL600;

*θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity;

Main application:

*Signage applications;

*Status indicator;

*Commercial and residential architectural lighting;

Green throguh-hole LED and SMD LED application

Detail:

This green color devices are made with Gap green light emitting diode. We produce this LED with high quality diffused lens and famous branded chip, and then use the pure gold wire inside for circuit connection.

312LGC-3.5HK 3mm LED Circuit Board Indictor detail

Precautions:

1, A moisture barrier bag(MBB)containing LEDS shall be kept in an environment with temperature below40C and humidity below 90% RH. A MBB shall be kept sealed until the LEDS contained in that bag are to be used immediately.Storge in an environment with temperature 5-30 C and humidity below 60% RH

2. After a MBB has been opened, all LEDS contained in that bag shall complete soldering process withinaccording to the conditions listed on the Best LED MBB.

3. If the 10% spot of a humidity indicator card (HIC)indicates wet, LEDS shall be baked according tothe conditions listed on the Best LED MBB.

4. During soldering, component covers and holders should leave clearance to avoid placing damagingstress on the LED during soldering.

Right Angle LED Circuit Board Indicator

5 . The tip of the soldering iron should never touch the lens epoxy；

6 . After soldering , allow at least three minutes for the component to cool down to room temperature before further operations；

7 . If the LED will undergo multiple soldering passes or face other processes where the part may be subjected to intense heat , please check with Best LED for compatibility；

8 . Recommended Reflow Soldering Profiles For SMD Housing LEDS;

Notes:

1, We recommend the reflow temperature 245℃(±5℃). The maximum soldering temperature should be limited to 260℃.

2, Don't cause stress to the epoxy resin whilte it is expossed to high tempreature.

3, Recommended solder: Sn/Cu/Ag;

4, No more than once;

You May Also Like

Contact Now

If you are interested in the product, contact 2bvideo.com for more information for more information

To:: Shenzhen Best LED Opto-electronic Co.,Ltd / BESTSMD CO LIMITED(HK)

Message:

Submit

Disclaimer：

The information of 2bvideo.com limited shown above is provided by the user or collected on the network. Video 2B does not guarantee the authenticity,accuracy and legitimacy of 2bvideo.com limited information. Video 2B does not involve legal relationships and disputes between users arising from transactions other than secured transactions on this website. Disputes shall be settled by you through negotiation. If you are the person in charge or relevant employee of this enterprise, if you find that the enterprise information is incorrect or want to manage thiscompany, please contact us jacklee1558@gmail.com, after you claim the enterprise, you can obtain management permission, publish supplyand demand information, bring consulting orders, and remove page advertisements.

Shenzhen Best LED Opto-electronic Co.,Ltd / BESTSMD CO LIMITED(HK)

 Audited supplier

8 year

Address: Shenzhen, China

Main Product: SMD LED , IR LED , Through-hole LED, RGB LED , Flashing LED, High-power LED

 Contact now